Bore Water Systems for Homes & Lifestyle Properties

Bore water systems assessed from source to tap

Brown staining, blocked filters, weak pressure or a pump that never stops cycling can point to problems at different stages of a bore water system. WaterForce designs, installs and services the complete pathway, from the bore pump through pressure, storage and treatment to the tap. We start by establishing what's actually happening: the source, a water test and your real peak demand. Then we design or improve the system around that evidence rather than simply increasing pump size.

COntact us
Crane lifting bore equipment beside WaterForce vehicles

Why WaterForce for bore water

Source-to-tap design

Pump, pressure, storage and treatment sized together as one hydraulic system.

Evidence before equipment

Water testing and real demand drive the design, so you only pay for the treatment the water actually needs.

Local system support

Practical advice, installation and servicing from WaterForce teams across New Zealand.

Built to be serviced

Every system is planned for access, filter changes and future maintenance, not just installation day.

How a bore water system works

A household bore system runs through connected stages: the bore accesses the groundwater, a correctly sized submersible pump lifts the water, a pressure vessel and controls maintain usable pressure, storage balances supply against demand where the bore recovery is slow, and treatment handles whatever the water test identifies before the water reaches the house. Change one stage without checking the others and you get low pressure, constant cycling or treatment that underperforms. That's why we design the lot together.

Pump, pipework and controls inside a pump shed

Pump sizing that respects the bore

Pump selection depends on the bore's yield and depth, total pumping head, pipe size and distance, and the flow needed when several outlets run together. A larger pump cannot create water the source can't sustainably provide, so where supply and peak demand don't line up, we design storage and controls that bridge the gap instead.

Water pressure pump with an electronic controller

Treatment designed from a water test

Clear-looking bore water can still carry hardness, iron, manganese, sediment or microorganisms, and conditions change over time. A water test gives the design a factual starting point, then each treatment stage does its own job: sediment filtration protects the equipment, a softener handles hardness, specialised media target iron and manganese, and UV disinfects. WaterForce specifies the stages the test justifies and leaves out the ones it doesn't.

Installed water filtration and UV treatment unit

Fixing an existing bore system

Inherited a bore with no records, mismatched components and three symptoms at once? A structured assessment separates a water-quality issue from a pump, pressure or control problem before anything gets replaced. Often the fix is smaller than the symptoms suggest.

WaterForce technician servicing a water pump

Frequently asked questions

Should bore water be tested?

Yes. Testing is the only reliable way to know what's in the water and what treatment it needs. Appearance, taste and odour can't identify everything present.

What size bore pump do I need?

It depends on bore yield and depth, total head, pipework and peak simultaneous demand. We calculate it as part of the system design; a bigger pump is rarely the answer to low pressure on its own.

What causes brown or orange staining?

Commonly iron or manganese, but sediment and pipework can produce similar symptoms. Test first, then treat the confirmed cause.

Does a UV system treat all bore water problems?

No. UV is a disinfection stage. It doesn't remove sediment, hardness, iron, manganese or dissolved chemicals, and it needs suitable pre-treatment to work properly.

Can one system treat the whole house?

Yes, when it's sized for the source, peak flow and the treatment the test identifies, and installed where it can be maintained.

Why does my pump keep cycling on and off?

Usually a pressure vessel, control or leak issue rather than the pump itself. It's worth diagnosing before replacing anything, because rapid cycling shortens pump life.

Do I need storage as well as a pressure vessel?

A pressure vessel smooths short-term demand; separate storage helps where bore recovery is slower than peak use or the property wants resilience between pumping cycles.

Can WaterForce upgrade an existing bore system?

Yes. We assess what's installed, test the water and recommend the smallest change that fixes the cause, whether that's a control adjustment, a treatment stage or a redesign.

Does WaterForce drill bores?

Talk to your local team before arranging the drilling. Depending on the project and region, the bore may be completed by a specialist drilling contractor, with WaterForce designing the pump, pressure, storage and treatment stages that follow.

How do I get started?

Send through your location, any bore depth or yield records, recent water tests, household size and photos of the existing equipment. Your local team will outline the assessment and options from there.

Get reliable water from your bore

WaterForce has designed, installed and supported water systems across New Zealand for over 20 years. Talk to your local team about a new bore system, or an existing one that isn't performing.

Get in Touch